Configurators

The RollMaster 280 configurator will help you choose the optimum set according to your needs.

First step is to choose the end cutter version. The Standard version's end cutter is moved manually, while the Super version offers automatic forward & back movement after pressing the start button. The main benefit of the automatic end cutter is speeding up work. It is not necessary to walk along the table pushing the cutter ahead and then go back to the start position – it is made automatically and takes just a few seconds.

Second step is the choice of holding bar. In the basic version it is operated manually using a handle. Operation is simple and fast, but worth considering is a pneumatic holding bar, as it offers the possibility to lift the bar temporarily by the additional pedal button. It is very useful when, after unrolling the material, you can see it is not set in the right angle. The pneumatic version allows one to lift the holding bar higher and is highly recommended when working with day-night/zebra type of roller blinds.

Guiding strip may be extended with a slider with an angle strip of 90 degrees or slider with laser, which help to measure the length of the cut. One move of an operator’s hand makes it possible to lock and change the position of the slider.

Another option to consider is the backlight on the table top. This helps to detect errors and cut off the faulty fragment of the material, saving the rest of fabric. It can vastly affect the material consumption.

The end cutter speed adjustment is helpful in cutting materials which stick on to the blade during high speed cutting. It mainly affects synthetic fabrics.

The fabric rolling machine is a simple tool designed for rolling material on the tube. It speeds up preparing a roller blind and helps to keep the material in the right angle. The fabric rolling machine can be operated either manually with an electric add-on driver (included) or automatically by using a foot pedal, which gives you both hands free.

Control frame helps to check the correctness of rolling-up the roller shade. The simple chain mechanism (or motor in electric version) allows to coil and unwind the roller shade to check if it is straight. Graspers for the tube are regulated. Width of the test frame can be adjusted, limited only with length of the table top.

The RollMaster XL configurator will help you choose the optimum set according to your needs.

First step is to choose the end cutter version. The Standard version's end cutter is moved manually, while the Super version offers automatic forward & back movement after pressing the start button. The strong point of the Standard version is the possibility of slow movement of the end cutter and stopping it during cutting operation, which can be useful with hard materials. The main benefit of the automatic end cutter is speeding up work. It is not necessary to walk along the table pushing the cutter ahead and then go back to the start position – it is made automatically and takes just a few seconds.

Guiding strip may be extended with a sliding strip with an angle of 90 degrees, which helps to measure the length of the cut. One move of an operator’s hand makes it possible to lock and change the position of the angle strip.

Low speed end cutter (600 rpm) will be better for cutting materials which stick on to the blade during high speed cutting. Before making a decision we recommend to send us samples of material for testing.

The table width should be matched with the maximum roll width you use. Cutting width is 10 cm less then a table width.

The length of the working top is practically unlimited. A standard length of the table top is 202 cm with the possibility of an extension up to 280 cm without joining tops.

The RollMaster 310 configurator will help you choose the optimum set according to your needs.

First step is the choice of holding bar. In the basic version it is operated manually using a handle. Operation is simple and fast, but worth considering is a pneumatic holding bar, as it offers the possibility to lift the bar temporarily by the additional pedal button. It is very useful when, after unrolling the material, you can see it is not set in the right angle. The pneumatic version allows one to lift the holding bar higher and it is recommended when working with thicker fabrics, as well as zebra/shangri-la type of roller blinds.

Guiding strip may be extended with a slider with an angle strip of 90 degrees or slider with laser, which help to measure the length of the cut. One move of an operator’s hand makes it possible to lock and change the position of the slider.

Another option to consider is the backlight on the table top. This helps to detect errors and cut off the faulty fragment of the material, saving the rest of fabric. It can vastly affect the material consumption.

The end cutter speed adjustment is helpful in cutting materials which stick on to the blade during high speed cutting. It mainly affects synthetic fabrics.

The fabric rolling machine is a simple tool designed for rolling material on the tube. It speeds up preparing a roller blind and helps to keep the material in the right angle. The fabric rolling machine can be operated either manually with an electric add-on driver (included) or automatically by using a foot pedal, which gives you both hands free.

Control frame helps to check the correctness of rolling-up the roller shade. The simple chain mechanism (or motor in electric version) allows to coil and unwind the roller shade to check if it is straight. Graspers for the tube are regulated. Width of the test frame can be adjusted, limited only with length of the table top.

The RollMaster Mini configurator will help you choose the optimum set according to your needs.

First step is to choose the version of end cutter. The Standard version's end cutter is moved manually, while the Super version offers automatic forward & back movement after pressing the start button. The main benefit of the automatic end cutter is speeding up work. Automatic end cutter in Super Plus version offers higher cutting capacity of single layer up to 2,5 cm (in Standard and Super versions - 0,8 cm) and is recommended for thick materials.

Guiding strip may be extended with a slider with an angle strip of 90 degrees or slider with laser, which help to measure the length of the cut. One move of an operator’s hand makes it possible to lock and change the position of the slider.

Another option to consider is the backlight on the table top. This helps to detect errors and cut off the faulty fragment of the material, saving the rest of fabric. It can vastly affect the material consumption.

The end cutter speed adjustment (only for Standard and Super version) is helpful in cutting materials which stick on to the blade during high speed cutting. It mainly affects synthetic fabrics.

The Ocean SK cutting table configurator will help you choose the optimum set according to your needs.

First step it to choose table width. We propose four main sizes - 182, 202, 222, 242 cm. Table width should be a little bigger than the widest roll you cut from.

Second step is the choice of table length. Planning space in the cutting room, please remember to leave 80 cm in front of the table and 50 cm at the back.

Bottom shelves are useful to store rolls of material and accessories needed in the cutting room, especially when you do not have a large space available. Table frame is prepared for adding bottom shelves at any moment, even if they are not ordered with the complete set.

Table legs can be equipped with casters with brakes, so it can be easily moved in the room. Table with wheels requires a hard and flat ground. There is no possibility of height adjustment in that case

For unrolling the fabric you can use one of three types of fabric unroller. Two of them are upper unrollers mounted on the table top. They come with one or two bars (second bar helps to reduce the tilt angle of material and keep it closer to the end cutter level). Lower unroller is attached to the frame and has two rollers located at the table top level.

In the next step you can choose the version of end cutter. DYDB-1 version is moved manually, while DYDB-2 offers automatic forward & back movement after pressing the start button. The main benefit of the automatic end cutter is speeding up work. Automatic end cutter in DYDB-2A version offers higher cutting capacity of single layer up to 2,5 cm (in DYDB-1 and DYDB-2 versions - 0,8 cm) and is recommended for thick materials.

In case of upper unwinder and end cutter we provide a useful roller guide of end cutter. It stretches the material on the cutting height and prevents the problem of uneven cuts, which may occur when the material is stretched diagonally going up.

Last option to choose is a holding bar. Basic version with parking brake is operated manually using a handle. Electric version is moved up and down by buttons, there is no need to use a brake as the holding bar is blocked after lifting until released. For 242 cm table only the manual version is supported.

The RollMaster cutting table configurator will help you choose the optimum set according to your needs.

First step it to choose table width. We propose three main sizes - 250, 280 and 310 cm. Table width is 10 cm bigger than cutting width. 

Second step is to choose the end cutter version. The Standard version is moved manually, while the Super version offers automatic forward & back movement after pressing the start button. The main benefit of the automatic end cutter is speeding up work. It is not necessary to walk along the table pushing the cutter ahead and then go back to the start position – it is made automatically and takes just a few seconds.

Next step is the choice of holding bar. In the basic version it is operated manually using a handle. Operation is simple and fast, but worth considering is an pneumatic holding bar, as it offers the possibility to lift the bar temporarily by the additional pedal button. It is very useful when, after unrolling the material, you can see it is not set in the right angle. The pneumatic version allows one to lift the holding bar higher and is highly recommended when working with day-night/zebra type of roller blinds. The electromagnetic version lifts lower than pneumatic and is only available for RollMaster 250.

Guiding strip may be extended with a slider with an angle strip of 90 degrees or slider with laser, which help to measure the length of the cut. One move of an operator’s hand makes it possible to lock and change the position of the slider.

Another option to consider is the backlight on the table top. This helps to detect errors and cut off the faulty fragment of the material, saving the rest of fabric. It can vastly affect the material consumption.

Fabric feeder can be located under tabletop, which saves space and ensures more convenient access to the table. Depending on your preference, you can also select the upper version of the feeder, matched to the height of the worktop. Last option is universal version, which position can be easily changed.

The end cutter speed adjustment is helpful in cutting materials which stick on to the blade during high speed cutting. It mainly affects synthetic fabrics.

The fabric rolling machine is a simple tool designed for rolling material on the tube. It speeds up preparing a roller blind and helps to keep the material in the right angle. The fabric rolling machine can be operated either manually with an electric add-on driver (included) or automatically by using a foot pedal, which gives you both hands free.

Control frame helps to check the correctness of rolling-up the roller shade. The simple chain mechanism (or motor in electric version) allows to coil and unwind the roller shade to check if it is straight. Graspers for the tube are regulated. Width of the test frame can be adjusted, limited only with length of the table top.

The CUTMaster configurator will help you choose the optimum set according to your needs.

1. First step it to choose table width. We propose four main sizes - 182, 202, 222, 242 cm. Table width should be a equal or bigger than the widest roll you cut from.

2. Second step is to choose the version of end cutter. The Standard version is moved manually, while the Super version offers automatic forward & back movement after pressing the start button. The main benefit of the automatic end cutter is speeding up work. Automatic end cutter in Super Plus version offers higher cutting capacity of single layer up to 2,5 cm
(in Standard and Super versions - 0,8 cm) and is recommended for thick materials.

3. Third step is the choice of the table length. Table is built in segments of about 1.5 m. When calculating the desired length you should take into account that spreading machine needs about 70 cm on the table top. Planning space in the cutting room, please remember to leave 80 cm in front of the table and 50 cm at the back.

4. Next step is to choose a holding bar. Basic version with parking brake is operated manually using a handle. Electric version is moved up and down by buttons, there is no need to use a brake as the holding bar is blocked after lifting until released.

5. Another option is a rotating bar of the spreader which makes it easy to quickly reverse the material side. It is very useful for fabrics with texture or patterns that are symmetrical to each match, such as the legs of trousers. Option not available in wider versions.

6. Smoothing roll smoothes the spreaded material resulting in wrinkles removal, especially on the knitted and lycra-type fabric, etc. Option not available in wider versions.

7. Bottom shelves are useful to store rolls of material and accessories needed in the cutting room, especially when you do not have a large space available. Table frame is prepared for adding bottom shelves at any moment, even if they are not ordered with the complete set.

8. Spreading board for pallets makes it easy to spread the material contained on the pallet. Just put a pallet on board and spread the material.

9. Power feed system should be chosen when there is no upper power feed system in the cutting room. We offer two types of power feed systems - bottom and upper.

10. Additional cones of bigger diameter will be useful for materials rolled on the thick tubes. Standard cones allow to mount tubes of diameter up to 45 mm.

The CUTMaster AIR configurator will help you choose the optimum set according to your needs.

1. First step it to choose table width. We propose four main sizes - 182, 202, 222, 242 cm. Table width should be a equal or bigger than the widest roll you cut from.

2. Second step is to choose the version of end cutter. The Standard version is moved manually, while the Super version offers automatic forward & back movement after pressing the start button. The main benefit of the automatic end cutter is speeding up work. Automatic end cutter in Super Plus version offers higher cutting capacity of single layer up to 2,5 cm 
(in Standard and Super versions - 0,8 cm) and is recommended for thick materials.

3. Third step is the choice of the table length. Table is built in segments of about 1.5 m. When calculating the desired length you should take into account that spreading machine needs about 70 cm on the table top. Planning space in the cutting room, please remember to leave 80 cm in front of the table and 50 cm at the back.

4. Next step is to choose a holding bar. Basic version with parking brake is operated manually using a handle. Electric version is moved up and down by buttons, there is no need to use a brake as the holding bar is blocked after lifting until released.

5. Another option is a rotating bar of the spreader which makes it easy to quickly reverse the material side. It is very useful for fabrics with texture or patterns that are symmetrical to each match, such as the legs of trousers. Option not available in wider versions.

6. Smoothing roll smoothes the spreaded material resulting in wrinkles removal, especially on the knitted and lycra-type fabric, etc. Option not available in wider versions.

7. Spreading board for pallets makes it easy to spread the material contained on the pallet. Just put a pallet on board and spread the material.

8. Power feed system should be chosen when there is no upper power feed system in the cutting room. We offer two types of power feed systems - bottom and upper.

9. Additional cones of bigger diameter will be useful for materials rolled on the thick tubes. Standard cones allow to mount tubes of diameter up to 45 mm.